connection
To prevent a socket from hanging open by a bad client the broker should
make sure to stop the transport if a connection attempt fails by an
OpenWire client
The method testStopConnectionDuringOnMessage in this class was relying
on sleep() calls for critical timing. This test fails sometimes on
fast-tests so I modified it to use a latch and a few waitFor calls to be
more deterministic. It also runs in a third of the time now.
Logging for the "fast-tests" profile used for PR builds could be reduced
significantly. This would save time as well as prevent log truncation
(Travis CI only supports logs up to 4MB).
Revert #1875
This reverts commit 5ad45369ce.
The storage manager is broken now as the AddressManager change here is trying to insert a record on the journal before startup.
- LargeServerMessageImpl.finalize is eventually causing deadlocks
- CoreMessage needs to check properties before decoding
- PagingTest tweaks
- ServerLocatorImpl can deadlock eventually, avoiding a lock and using actors
- ActiveMQServerImpl.finalize is also evil and can cause deadlocks on the testsuite
- MqttClusterRemoteSubscribeTest needs to setup the Address now on the setup
The PageCountPendingImpl was increasing the encode size without using its full allocation.
This was causing issues on replication as the encode is also used to determine the size of the packets.
however the packets were not receive the full allocated data causing missing packets on the replication
and test failures.
This is fixing the issue
Adding new metrics for tracking message counts and sizes on a Queue.
This includes tracking metrics for pending, delivering and scheduled
messages. The paging store also tracks message size now.
Support exlusive consumer
Allow default address level settings for exclusive consumer
Allow queue level setting in broker.xml
Add the ability to set queue settings via Core JMS using address. Similar to ActiveMQ 5.X
Allow for Core JMS client to define exclusive consumer using address parameters
Add tests
Make sure that if a bridge disconnects and there is no record in the topology that it uses the original bridge connector to reconnect.
Originally the live broker that disconnected was left in the Topology, thie broke quorum voting as when th evote happened all brokers when asked though th etarget broker was still alive.
The fix for this was to remove the target live broker from the Topology. Since the bridge reconnect logic relied on this in a non HA environment to reconnect this stopped working.
The fix now uses the original target connector (or backup) to reconnect in the case where the broker was actually removed from the cluster.
https://issues.apache.org/jira/browse/ARTEMIS-1654
When using the tool to import more than one large messages
from xml exported file, this utility class will create some
tmp files, each for one large message. However it only delete
one of the tmp files. All the rest of tmp files won't get
cleaned up.
HornetQClientProtocolManager is used to connect HornteQ servers.
During reconnect, it sends a CheckFailoverMessage packet to the
server as part of reconnection. This packet is not supported by
HornetQ server (existing release), so it will break the backward
compatibility.
Also fixed a failover issue where a hornetq NettyConnector's
ConnectorFactory is serialized to the clients who cannot
instantiate it because class not found exception.
ActiveMQTestBase has been enhanced to expose the Database storage configuration and by adding specific JDBC HA configuration properties.
JdbcLeaseLockTest and NettyFailoverTests have been changed in order to make use of the JDBC configuration provided by ActiveMQTestBase.
JdbcNodeManager has been made restartable to allow failover tests to reuse it after a failover.
Test consistency between live and backup, espacially on
a slow live.
The test use MessagePersister::encode to simulate slow IO condition.
After live started, we send 5 message with a delay(default 500ms),
then start backup, wait until replicated, then send more message
without delay. If all message sent successfully, the backup should
has the same messages as live. We assert the message number only.
Flag needs to be set when auto creating an address so that the address
can be removed later if auto delete is configured when creating a
subscription with MQTT
We provide a feature to mask passwords in the configuration files.
However, passwords in the bootstrap.xml (when the console is
secured with HTTPS) cannot be masked. This enhancement has
been opened to allow passwords in the bootstrap.xml to be masked
using the built-in masking feature provided by the broker.
Also the LDAPLoginModule configuration (in login.config) has a
connection password attribute that also needs this mask support.
In addition the ENC() syntax is supported for password masking
to replace the old 'mask-password' flag.
Change all use from Set<RoutingType> to EnumSet<RoutingType>
Deprecating any old exposed interfaces but keeping for back compatibility.
Address info to avoid iterator on getRoutingType hotpath, like wise can be avoided where single RoutingType is passed in.
When an address is removed from the address manager its linked addresses
also need to be removed if there are no more bindings for the address.
Also adding a null check on bindings of linked addresses when a new
binding is added
The UTF translations has been improved by:
- zero copy on array based buffers
- zero copy UTF length calculation
- faster array access using Netty PlatformDependent.get|putByte
- improved perf tests UTF8Test
* Move byte util code into ByteUtil
* Re-use the new equals method in SimpleString
* Apply same pools/interners to client decode
* Create String to SimpleString pools/interners for property access via String keys (producer and consumer benefits)
* Lazy init the pools on withing the get methods of CoreMessageObjectPools to get the specific pool, to avoid having this scattered every where.
* reduce SimpleString creation in conversion to/from core message methods with JMS wrapper.
* reduce SimpleString creation in conversion to/from Core in OpenWire, AMQP, MQTT.
Replace GenericSQLProvider and other implementation by a single
PropertySQLProvider that uses properties to define SQL queries.
SQL queries are loaded from the journal-sql.properties file.
Queries specific to a DB dialect can be specified by adding a suffix to
the key of the generic property.
For example, the generic property to create a file Table is:
create-file-table = CREATE TABLE %s (ID BIGINT AUTO_INCREMENT, ...)
This property can be customized for Derby by using the
create-file-table.derby property:
create-file-table.derby=CREATE TABLE %s (ID BIGINT NOT NULL GENERATED ALWAYS AS IDENTITY (START WITH 1, INCREMENT BY 1),...
JIRA: https://issues.apache.org/jira/browse/ARTEMIS-1590
The test is using the wrong indices for the destinations it uses so they
don't match the one's created in the test support class. Because the
code is now using the default routing type the test fails when it tries
to send a message on a JMS Queue when the auto created address default
to the multicast routing type.
Clebert Suconic
Stanislav Knot
Justin Bertram
JiriOndrusek
jpoth
Christopher L. Shannon (cshannon)
17103355
raul.valdoleiros
Michael André Pearce
Martyn Taylor
Guillaume Nodet
Andy Taylor
Howard Gao
Pat Fox
Francesco Nigro
Robbie Gemmell
jostbg
Jeff Mesnil
gtully
shoukun
Timothy Bish