98 lines
3.8 KiB
Plaintext
98 lines
3.8 KiB
Plaintext
[[discovery-file]]
|
|
=== File-Based Discovery Plugin
|
|
|
|
The file-based discovery plugin uses a list of hosts/ports in a `unicast_hosts.txt` file
|
|
in the `config/discovery-file` directory for unicast discovery.
|
|
|
|
[[discovery-file-install]]
|
|
[float]
|
|
==== Installation
|
|
|
|
This plugin can be installed using the plugin manager:
|
|
|
|
[source,sh]
|
|
----------------------------------------------------------------
|
|
sudo bin/elasticsearch-plugin install discovery-file
|
|
----------------------------------------------------------------
|
|
|
|
The plugin must be installed on every node in the cluster, and each node must
|
|
be restarted after installation. Note that installing the plugin will add a
|
|
`discovery-file` directory to the `config` folder, and a default `unicast_hosts.txt`
|
|
file that must be edited with the correct unicast hosts list before starting the node.
|
|
|
|
[[discovery-file-remove]]
|
|
[float]
|
|
==== Removal
|
|
|
|
The plugin can be removed with the following command:
|
|
|
|
[source,sh]
|
|
----------------------------------------------------------------
|
|
sudo bin/elasticsearch-plugin remove discovery-file
|
|
----------------------------------------------------------------
|
|
|
|
The node must be stopped before removing the plugin.
|
|
|
|
[[discovery-file-usage]]
|
|
[float]
|
|
==== Using the file-based discovery plugin
|
|
|
|
The file-based discovery plugin provides the ability to specify the
|
|
unicast hosts list through a simple `unicast_hosts.txt` file that can
|
|
be dynamically updated at any time. To enable, add the following in `elasticsearch.yml`:
|
|
|
|
[source,yaml]
|
|
----
|
|
discovery.zen.hosts_provider: file
|
|
----
|
|
|
|
This plugin simply provides a facility to supply the unicast hosts list for
|
|
zen discovery through an external file that can be updated at any time by a side process.
|
|
|
|
For example, this gives a convenient mechanism for an Elasticsearch instance
|
|
that is run in docker containers to be dynamically supplied a list of IP
|
|
addresses to connect to for zen discovery when those IP addresses may not be
|
|
known at node startup.
|
|
|
|
Note that the file-based discovery plugin is meant to augment the unicast
|
|
hosts list in `elasticsearch.yml` (if specified), not replace it. Therefore,
|
|
if there are valid unicast host entries in `discovery.zen.ping.unicast.hosts`,
|
|
they will be used in addition to those supplied in `unicast_hosts.txt`.
|
|
|
|
Anytime a change is made to the `unicast_hosts.txt` file, even as Elasticsearch
|
|
continues to run, the new changes will be picked up by the plugin and the
|
|
new hosts list will be used for the next pinging round for master election.
|
|
|
|
Upon installation of the plugin, a default `unicast_hosts.txt` file will
|
|
be found in the `$CONFIG_DIR/discovery-file` directory. This default file
|
|
will contain some comments about what the file should contain. All comments
|
|
for this file must appear on their lines starting with `#` (i.e. comments
|
|
cannot start in the middle of a line).
|
|
|
|
[[discovery-file-format]]
|
|
[float]
|
|
==== unicast_hosts.txt file format
|
|
|
|
The format of the file is to specify one unicast host entry per line.
|
|
Each unicast host entry consists of the host (host name or IP address) and
|
|
an optional transport port number. If the port number is specified, is must
|
|
come immediately after the host (on the same line) separated by a `:`.
|
|
If the port number is not specified, a default value of 9300 is used.
|
|
|
|
For example, this is an example of `unicast_hosts.txt` for a cluster with
|
|
four nodes that participate in unicast discovery, some of which are not
|
|
running on the default port:
|
|
|
|
[source,txt]
|
|
----------------------------------------------------------------
|
|
10.10.10.5
|
|
10.10.10.6:9305
|
|
10.10.10.5:10005
|
|
# an IPv6 address
|
|
[2001:0db8:85a3:0000:0000:8a2e:0370:7334]:9301
|
|
----------------------------------------------------------------
|
|
|
|
Host names are allowed instead of IP addresses (similar to
|
|
`discovery.zen.ping.unicast.hosts`), and IPv6 addresses must be
|
|
specified in brackets with the port coming after the brackets.
|