This is caused by too many entries on the HashMap for ThreadLocals.
Also: I'm reviewing some readlock usage on the StorageManager to simplify things a little bit.
JMSTestCase is deprecated anyway.
in its older form many many years ago a server would be reused over
between tests.
what forced us to make such verification to avoid messages from one test
leaking into the next.
This was because a server startup was expensive many years ago (less
efficient code and the hardware available 10 years ago)
with the current state of things this is not needed as the server will
be started from scratch on every test
It would be useful to be able to cycle the embedded web server if, for
example, one needed to renew the SSL certificates. To support
functionality I made a handful of changes, e.g.:
- Refactoring WebServerComponent so that all the necessary
configuration would happen in the start() method.
- Refactoring WebServerComponentTest to re-use code.
It would be useful for security manager implementations to be able to
alter the client ID of MQTT connections.
This commit supports this functionality by moving the code which handles
the client ID *ahead* of the authentication code. There it sets the
client ID on the connection and thereafter any component (e.g. security
managers) which needs to inspect or modify it can do so on the
connection.
This commit also refactors the MQTT connection class to extend the
abstract connection class. This greatly simplifies the MQTT connection
class and will make it easier to maintain in the future.
Allow replication only certain addresses with mirror controller.
The configuration is similar to cluster address configuration.
Co-authored-by: Robbie Gemmell <robbie@apache.org>
The control existing in Redistributor is not needed as the Queue::deliver will already have a control on re-scheduling the loop and avoid holding references for too long.
When running a UDP connection factory you have to either keep it running, or close it so the UDP thread is closed.
this is an issue for the testsuite as we validate for leaked threads. This needs to be fixed on the test.
The MQTT 5 (and 3.1.1) specification states:
Until it has received the corresponding PUBREL packet, the receiver
MUST acknowledge any subsequent PUBLISH packet with the same Packet
Identifier by sending a PUBREC. It MUST NOT cause duplicate messages to
be delivered to any onward recipients in this case [MQTT-4.3.3-10].
The broker prevents a duplicate message, but it doesn't respond with a
PUBREC. This commit fixes that.
Removing the connection ID property from the actual *message* breaks the
nolocal functionality. Removing the property isn't necessary in the
first place so this commit reomves that code.
It is possible to receive a compressed message from the client as regular message. Such a message will already contain correct body size, that takes compression into account.
Older versions of Openwire clients wil be affected by AMQ-6431.
As a result of the issue if the ID of the message>Integer.MAX_VALUE
a consumer configured with Failover and doing duplicate detection on the client
will not be able to process duplicate detection accordingly and miss messages.
Paging only removes files at the beginning of the stream...
Say you have paged files 1 through 1000...
if all the messages are ack, but one message on file 1 is missing an ack, all the 999 subsequent files would not be removed until all the messages on file 1 is ack.
This was working as engineered, but sometimes devs don't have complete control on their app.
With this improvement we will now remove messages in the middle of the stream as well.
There is also some improvement to how browsing and page work with this
Scripts:
- Fix the preapre-docker.sh to exit with 0 instead of 1 on success
On pom files:
- Change e2e-tests variable names to e2e-tests.xxxxxx for clarity on
e2e-tests variables
- Add e2e-tests.skipImageBuild variable to control if the docker image
will be build (defaults to not build)
- Add e2e-tests.dockerfile variable to specify the dockerfile to be
used (defaults to Dockerfile-centos)
- Bump testcontainers version to 1.16.3
- Add artemis distribution dependency since the docker image build
depends on it
On ContainerService class:
- Fix exposePorts and exporseFolder to use SELinux shared mode
otherwise the mount fails on machines with SELinux enabled
- Move the logic to use specific user on container from generic start
method to broker specific method to avoid affect other images
- Update the broker image name to a more generic name (activemq-artemis
instead of artemis-centos)
- Update the broker image tag to match with the project version in pom
file
As the test needs the generated jms jars to be verified I moved it from
unit-tests to smoke-tests.
Updated the test to look for the correct jars as the originally
specified does not exist.
Update the test to assert against Implementation-Version instead of
ActiveMQ-Version in the manifest file as the ActiveMQ-Version property does not exist.
Move all tests which are related to end-to-end testing from smoke-tests
module to a new module named e2e-tests.
These e2e tests are those which are dependent of ContainerService
class. ContainerService class uses artemis inside a container by using
the testcontainers library and for that reason these tests are usually
a quite slow and tecnically they are not a smoke test.
The new e2e-tests module is part of tests module but it is not enabled
by default and to get executed it requires the e2e-tests profile
specification on maven command.
The commit includes the following changes:
- Don't drop the connection on subscribe or publish authorization
failures for 3.1 clients.
- Don't drop the connection on subscribe authorization failures for
3.1.1 clients.
- Add configuration parameter to control behavior on publish
authorization failures for 3.1.1 clients (either disconnect or not).
When using a temporary queue with a `temporary-queue-namespace` the
`AddressSettings` lookup wasn't correct. This commit fixes that and
refactors `QueueImpl` a bit so that it holds a copy of its
`AddressSettings` rather than looking them up all the time. If any
relevant `AddressSettings` changes the
`HierarchicalRepositoryChangeListener` implementation will still
refresh the `QueueImpl` appropriately.
The `QueueControlImpl` was likewise changed to get the dead-letter
address and expiry address directly from the `QueueImpl` rather than
looking them up in the `AddressSettings` repository.
I modified some code that came from ARTEMIS-734, but I ran the test that
was associated with that Jira (i.e.
`o.a.a.a.t.i.c.d.ExpireWhileLoadBalanceTest`) and it passed so I think
that should be fine. There actually was no test included with the
original commit. One was added later so it's hard to say for sure it
exactly captures the original issue.
When copying message properties from the core message to the OpenWire
message we intentially omit any properties starting with `_AMQ` and
`__HDR_`. However, we were effectively negating that logic because we
copied the marshalled properties directly to the message without any
filtering. Now that we no longer copy the marshalled properties directly
to the message the test breaks because it expects properties starting
with `__HDR_`. This commit fixes the test by removing those
expectations. The test is still valid because the message is still
receieved rather than being swallowed due to an exception (which was the
original problem).
I am adding a test showing it is safe to not wait pending callbacks before closing a file.
With this I can just close the file and let the kernel to deal with sending the completions.
It sometimes makes sense to set an acceptor's port to 0 to allow the JVM
to select an ephemeral port (e.g. in embedded integration tests). This
commit adds a new getter on NettyAcceptor so tests can programmtically
determine the actual port used by the acceptor.
This commit also changes the ACCEPTOR_STARTED notification and the
related logging to clarify the actual port value where clients can
connect.
Avoid storing the following values as byte[] for OpenWire:
- Marshalled properties. We already store the unmarshalled properties
so this is altogether redundant.
- Producer ID.
- Message ID.
- Various destination values.
Also, eliminate the "original transaction ID" conversion code as it's
never actually set from the incoming message.
The auto-create-jms-queues, auto-delete-jms-queues,
auto-create-jms-topics, and auto-delete-jms-topics address settings
were deprecated in ARTEMIS-881 way back in 2016. There's no need to keep
them in the default broker.xml at this point.
JGroups 3.x hasn't been updated in some time now. The last release was
in April 2020 almost 2 years ago. Lots of protocols have been updated
and added and users are wanting to use them. There is also increasing
concern about using older components triggered mainly by other
recently-discovered high-profile vulnerabilities in the wider Open
Source Java community.
This commit bumps JGroups up to the latest release - 5.2.0.Final.
However, there is a cost associated with upgrading.
The old-style properties configuration is no longer supported. I think
it's unlikely that end-users are leveraging this because it is not
exposed via broker.xml. The JGroups XML configuration has been around
for a long time, is widely adopted, and is still supported. I expect
most (if not all) users are using this. However, a handful of tests
needed to be updated and/or removed to deal with this absence.
Some protocols and/or protocol properties are no longer supported. This
means that users may have to change their JGroups stack configurations
when they upgrade. For example, our own clustered-jgroups example had to
be updated or it wouldn't run properly.
Clebert Suconic
clebert
Justin Bertram
AntonRoskvist
Gary Tully
Domenico Francesco Bruscino
iliya
Robbie Gemmell
Emmanuel Hugonnet
Tiago Bueno
nbrendah
Matteo Baccan
Luis De Bello